Welcome, and congratulations on your new Halos 3-Wheel Light-Up Kick Scooter. Its stable three-wheel base and lean-to-steer design help developing riders build balance and confidence, while the light-up deck and motion-activated wheels add colorful fun to every ride. This guide walks you through assembling, adjusting, and riding your scooter.
Things you need to know
Preparation
- Read the complete user manual and all safety warnings before using the scooter.
- Adult assembly and adult supervision are required.
- Remove all protective packaging before beginning setup.
- Have three new AA batteries ready for the deck lights. Batteries are not included.
- Confirm the rider is at least 3 years old and does not exceed the 110 lb weight limit.
- Have an ASTM F1492-approved helmet, knee pads, elbow pads, and closed-toe, flat shoes ready.
- Choose a smooth, flat riding surface away from roadways, motor vehicles, steep inclines, steps, water, and debris.
What comes in the box
- Halos 3-Wheel Light-Up Kick Scooter
- 2-bit tool with a Phillips-head screwdriver and 5 mm Allen key
Tools required
- Included 2-bit Phillips-head screwdriver and 5 mm Allen key tool
Step-by-step setup
- Attach the stem. Position the stem over the scooter base with the handlebar at the top and the stem release button facing the back of the scooter. Press in the release button and slide the stem into the stem mount until the button clicks into the release-button hole. Check that the stem is securely attached. Warning:
Keep small parts away from children during assembly. The scooter must be assembled by an adult.
-
Adjust the handlebar height.
Use the 5 mm Allen key end of the included tool to loosen the stem-clamp knob by turning it counterclockwise. Pull open the stem-clamp latch. Press in the stem pin and raise or lower the handlebar until the pin clicks into the desired stem-pin hole. Close the latch, tighten the knob clockwise with the Allen key, and confirm that the handlebar is secure.
Important:
The stem pin alone will not keep the handlebar secure. The stem clamp must be tightened and closed before every ride.
Helpful tip:Do not overtighten the stem-clamp knob. Overtightening can prevent the latch from opening or closing properly.
-
Install the batteries.
Turn the scooter over to access the battery compartment on the underside of the deck. Use the Phillips-head screwdriver end of the included tool to loosen and remove the compartment-cover screw by turning it counterclockwise. Lift off the cover and install three AA batteries according to the positive and negative markings inside the compartment. Reposition the cover, reinsert the screw, and tighten it clockwise.
Warning:
Do not mix old and new batteries or mix alkaline, standard carbon-zinc, and rechargeable batteries.
-
Complete a pre-ride safety check.
Confirm that the stem, handlebar, stem clamp, wheels, guards, and other components are securely attached and in serviceable condition. Check that the rear foot brake works properly, all safety labels are present, and no parts are worn, loose, damaged, or missing.
Safety:
Do not ride if any part is loose, worn, broken, or missing. Replace worn or broken parts immediately, and contact the Jetson Care Team if assistance is needed.
-
Start moving.
Put on your helmet and protective gear. Place one foot on the front of the deck facing forward. Push your other foot against the ground to propel the scooter, repeating as needed to reach or maintain a comfortable speed. When coasting, place the kicking foot on the deck behind the front foot at a slight outward angle.
Warning:
Allow only one rider at a time. Do not perform stunts, race, ride at night, or use the scooter on roadways, uneven terrain, slopes, or wet surfaces.
-
Lean to steer.
While moving forward, gently lean toward the left or right. The scooter will veer in the direction of the lean.
Important:
The Halos uses lean-to-steer operation. Turn by gently leaning while the scooter is moving, and avoid sudden or abrupt turns.
-
Slow down and stop.
Press down gently on the rear foot brake with your rear riding foot to reduce your speed. Apply more pressure to come to a complete stop.
Warning:
Do not apply the brake too hard or too suddenly. Sudden or excessive braking can cause a loss of control and a fall. The brake may become hot during use, so do not touch it with bare skin.
Using the LED lights
Quick-press the lighting button to turn on the scooter’s battery-powered lights. Continue quick-pressing the button to cycle through the available lighting patterns.
To turn off the lights without cycling through every pattern, press and hold the lighting button for 3 seconds. The lights will also turn off automatically after 5 minutes without use. Quick-press the button to reactivate them.
The wheel lights are motion-activated and illuminate whenever the wheels are moving, even when the battery-powered lights are turned off.
Turn off the battery-powered lights when the ride is finished to preserve battery life.
Removing the stem for storage
Press in the stem release button and pull the stem upward and out of the stem mount. To reattach it, position the stem over the mount with the release button facing the back of the scooter. Press in the button and slide the stem into the mount until the button clicks into place.
After reinstalling the stem, confirm that the release button has clicked fully into its hole and the stem is securely attached before riding.
Quick troubleshooting
If the stem-clamp latch will not open or close: The clamp knob may be too tight. Loosen the knob a small amount at a time until the latch can open and close properly.
If the handlebar feels loose: Confirm that the stem pin has clicked fully into a stem-pin hole. Close the stem-clamp latch and tighten the knob clockwise with the included Allen key until the handlebar is secure. Do not overtighten the knob.
If the battery-powered lights do not turn on: Check that three AA batteries are installed according to the positive and negative markings. Replace them with three new matching batteries if needed, and confirm that the battery-compartment cover is securely closed.
If the lights turn off while the scooter is not being used: The lights automatically turn off after 5 minutes without use. Quick-press the lighting button to reactivate them.
If the wheel lights do not illuminate: The wheel lights are motion-activated and illuminate only when the wheels are moving. Roll the scooter forward to activate them.
If the scooter does not turn as expected: The Halos uses lean-to-steer operation. While moving forward, gently lean toward the direction you want to travel instead of trying to make an abrupt turn.
You are ready to ride
That is it—your Halos 3-Wheel Light-Up Kick Scooter is assembled, adjusted, and ready to roll. Start slowly on a smooth, flat surface while the rider becomes comfortable kicking, coasting, steering, and braking. Always wear a helmet and protective gear, and ride with adult supervision. Be safe and have fun!