Welcome, and congratulations on your new Fizz Bubble Ride-On. This guide walks you through identifying the color model, assembling the ride-on, preparing the bubble feature, completing the pre-ride checks, helping the rider make their first moves, and caring for the product.
Things you need to know
Available colors and model SKUs
- Sky Blue: JFIZZ-BLU
- Dusty Pink: JFIZZ-PNK
Preparation
- Read the full user manual and all safety warnings before assembly or use.
- Adult assembly and adult supervision are required.
- Confirm the rider is 18 months to 3 years old and weighs no more than 66 lb.
- Have the rider wear an ASTM F1492-approved helmet, protective gear, and closed-toe, flat shoes.
- Choose a smooth, flat indoor riding area away from roadways, motor vehicles, steep inclines, steps, swimming pools, water, sand, gravel, dirt, leaves, sharp bumps, drainage grates, and other hazards.
- Keep all small parts and bubble solution away from children during assembly.
What comes in the box
- Frame
- Handlebar and two handgrips
- Front fork, front wheel, and front fender
- Decorative headlight
- Two rear wheels and two hub caps
- Bubble machine component and bubble solution container
- Rear axle, front axle, M8 × 122 mm bolt with nut, assembly screws, and two M8 socket wrenches
- Phillips-head screwdriver
Additional items required
- Two AA batteries for the bubble and sound feature
- Commercially available bubble solution
Step-by-step setup
-
Remove the packaging. Remove all protective packaging pieces and organize the parts and hardware on a clean, stable surface.
Warning: The ride-on must be assembled by an adult. Keep small parts away from children during assembly. -
Attach the rear wheels. Follow the axle and hardware order shown in the user manual. Pass the rear axle through the rear of the frame, install one rear wheel on each side with the supplied washers and fasteners, and use both M8 socket wrenches to tighten the axle hardware securely. Press one hub cap onto the outside of each rear wheel.
Important: Keep every washer, spacer, and fastener in the exact order shown in the manual. Confirm both rear wheels are secure and rotate freely. - Assemble the front unit. Slide a handgrip fully onto each end of the handlebar. Position the handlebar and decorative headlight on the front fork as shown in the manual, then install and tighten the supplied screws with the Phillips-head screwdriver.
- Attach the front unit to the frame. Align the assembled front fork with the front of the frame. Insert the supplied M8 × 122 mm bolt through the aligned openings, install the supplied hardware in the order shown in the manual, and tighten the nut securely using both M8 socket wrenches.
- Attach the front fender. Position the fender between the front-fork arms with its longer section extending toward the rear. Align the mounting holes, insert the supplied screws, and tighten them securely with the Phillips-head screwdriver.
-
Attach the front wheel. Place the front wheel between the fork arms. Install the front axle, washers, and fasteners in the exact order shown in the manual, then use both M8 socket wrenches to tighten the axle hardware securely.
Safety: Confirm the front wheel is centered, secured to the fork, and able to rotate freely before use. -
Connect and attach the bubble machine. At the rear of the frame, connect the bubble-machine wire to the matching frame connector. Position the bubble machine under the rear body panel, align its mounting holes, and secure it with the supplied screws.
Important: Make sure the electrical connectors are fully joined and the wire is not pinched before securing the bubble machine. -
Fill and attach the bubble solution container. Twist the container counterclockwise to remove it. Add commercially available bubble solution without overfilling, then twist the container clockwise onto the bubble machine until secure.
Warning: Bubble solution is not for human consumption. Keep it away from the eyes. If it contacts the eyes, flush thoroughly with water. -
Install the batteries. Use the flat side of the Phillips-head screwdriver to turn the seat lock knob clockwise, then lift the seat. Remove the screw and battery-compartment cover, install two AA batteries according to the marked polarity, and reinstall the cover and screw. Reposition the seat and turn the lock knob counterclockwise to secure it.
Important: Do not mix old and new batteries or different battery types. Confirm the battery cover, screw, seat, and seat lock knob are secure. -
Test the bubble and sound feature. Press the bubbles and sound button once to turn the feature on. Confirm that bubbles dispense from the rear and the sound plays, then press the button again to turn the feature off.
Helpful tip: Always turn the bubble and sound feature off after the ride. - Complete the pre-ride checks. Confirm the handlebar is securely tightened, the handlebar and front wheel turn together, all three wheels are secured and rotate freely, and no wheel has excessive wear or damage.
-
Practice riding. With close adult supervision, have the rider sit securely, push both feet against the ground to move forward, lift both feet briefly to coast, rotate the handlebar gently to turn, and place both feet on the ground to stop.
Warning: Allow only one rider at a time. Do not use the ride-on for racing, stunts, abrupt turns, high-speed riding, uneven terrain, slopes, roadways, or near motor vehicles.
Riding and caring for the ride-on
The Fizz Bubble Ride-On is designed for supervised, foot-powered riding on a smooth, flat surface:
- Move: While seated, the rider pushes both feet against the ground to propel forward.
- Coast: Once moving, the rider may lift both feet briefly while maintaining balance.
- Turn: The rider rotates the handlebar gently to the left or right.
- Stop: The rider places both feet securely on the ground.
- Use bubbles and sound: Press the button once to turn the feature on and again to turn it off.
- Refill bubble solution: Remove the container counterclockwise, refill without overfilling, and reinstall it clockwise.
- Clean: Carefully wipe the ride-on with a damp cloth, then dry it with a dry cloth. Do not apply water directly to the product.
- Store: Keep the ride-on indoors in a dry place and cover it to protect it from dust.
Quick troubleshooting
If the bubbles and sound do not turn on: Press the button once, then check that two AA batteries are installed according to the marked polarity and that the battery-compartment cover and screw are secure. Replace the batteries if needed without mixing old and new batteries or different battery types.
If the bubble machine runs but does not make bubbles: Turn the feature off, confirm the container has commercially available bubble solution, check that it is not overfilled, and make sure the container is threaded securely onto the machine.
If the bubble machine does not respond after checking the batteries: Turn the feature off and have an adult confirm the bubble-machine wire connector is fully joined and not pinched. Contact Jetson Support if the issue continues.
If the handlebar and front wheel do not turn together: Stop using the ride-on. Recheck that the front unit and handlebar are securely assembled and contact Jetson Support if the steering still does not operate correctly.
If a wheel does not rotate freely or is damaged: Do not use the ride-on. Check for visible debris, loose hardware, wear, or damage and contact Jetson Support for assistance.
You are ready to ride
Your Fizz Bubble Ride-On is assembled and ready for supervised practice. Begin on a smooth, flat indoor surface, keep the rider at a slow pace, and complete the steering and wheel checks before every ride.